Question: The d = 1 2 - m m - diameter solid rod passes through a D = 1 7 - m m - diameter hole

The d=12-mm-diameter solid rod passes through a D=17-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b=11mm. The rod head has a diameter of a=24mm, and the head has a thickness of t=9mm. The shear stress in the rod head cannot exceed 130 MPa , the punching shear stress in the support plate cannot exceed 100 MPa , and the bearing stress between the rod head and the support plate cannot exceed 120 MPa . Determine the maximum value of Pmax that can be supported by the structure.
Answer: Pmax= kN
The d = 1 2 - m m - diameter solid rod passes

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Prob. 3.7-3. A pipe-rod system with flanges at ends A and C was supposed to fit exactly between two rigid walls, as shown in Fig. P3.7-3. Element (1) is a steel pipe with outside diam- eter d, and...

Q:

Experimental procedure 1. Tare a clean and dry 150 mL beaker on a balance. 2. Add about 1 g of copper turnings to the tared beaker, and record the mass of copper in grams, to a precision of 4 decimal...

Q:

1. Rod A has twice the diameter of rod B, but both are made of iron and have the same initial length. Both rods are now subjected to the same change in temperature (but remain solid). How would the...

Q:

can you explain the process when you doing this ,Thankssssss You are designing a plate that allows some water to go through it. A 10cm diameter jet of water exposed to the atmosphere) with a velocity...

Q:

In a mass spectrometer, charged particles are injected into a region of uniform magnetic field (all with the speed), where they travel along circular trajectories and are collected after completing...

Q:

Please help with the following request: Goals Learn test-driven development. Learn more about classes, objects, and inheritance. Learn to handle thrown exceptions. Problem The Weight program is not...

Q:

10 AL= Lia At VR=VitOV AB= BisB-SmallB LEZLitAL TE= TI1ST AVEVIBAT DVEVIC AB 207 PHYSICS WORKSHEET 3a=B AL = Li Ca ) At THERMAL EXPANSION Da = Biga-shalla 1. A metal rod, observed to be 102. 302 em...

Q:

6. . You nd a long silver metal rod with a circular crOSS-section and you measure its cross-section diameter to be 1 mm. You set the rod up in a way that a current of 2 A passes through its...

Q:

Example file: How to use mathlab to code this? THis is from INTRODUCTION TO OPTIMUM DESIGN. Problem# 3.34 Print Your Name Here and on Backside esign a hollow torsion rod shown in Fig.E3.34 to satisfy...

Q:

Initials: Problem 5 - 25 points The device shown in the figure is used to measure fluid speeds. The two coaxial tubes are designed such that the inner tube has a small opening at point 1, which is...

Q:

Pina Colada Corp's gross payroll for April is $49,400. The company deducted $2,262 for CPP. $1,013 for El, and $9,091 for income taxes from the employees' cheques. Employees are paid monthly at the...

Q:

Using the above information for Monitor Services PLC, the Return on Capital Employed: a) has improved from 40.3% to 56.4%

Q:

In this lesson, you will submit a yearly budget based on the specific salary from the career path activity earlier in the lesson. As you work to create your budget, be sure to complete all of the...

Q:

Subscribe What's the "carrying value" of a bond payable? What's the only condition where a bond carrying value will not change over its term until redeemed? (am assuming a "term" type bond, p. 751)