Question: Truss Calculation AB For the truss shown, if a is 8.1 m and P is 9.5 kN, determine the magnitude of the force in

Truss Calculation AB For the truss shown, if a is 8.1 m

Truss Calculation AB For the truss shown, if a is 8.1 m and P is 9.5 kN, determine the magnitude of the force in Member AB. (Hibbeler) Provide your answer in kN and to two decimal points Za

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

To solve this problem well use the method of joints and trigonometry to determine the force in membe... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Discuss the difference between board of Directors and Shareholders, provide case analysis philippine company about this topic.

for this reaction? a) What is the rate law for this reaction? b) What is the rate constant for this reaction? Don't forget units! c)A two-step mechanism is proposed for this reaction. Write the...

A non-symmetrical rigid jointed portal frame ABCDE is fixed at A, pinned at D and supported by a roller at E. It carries a trapezoidal distributed load acts along beam AB and a point load in span BC...

The Chief Operating Officer (COO) asked you to suggest how to improve the patient check-in process at a hospital. Currently, patients experience significant delay during the check-in process and, in...

Question 1 The frame supports the point load P at point C. The pins at A and B have diameters of 50 mm and 64 mm respectively. Pin A is in single shear, while Pin B is in double shear, and both pins...

Q 1 ) Determine the force in each member of the truss shown and state whether each member is in tension or compression by filling in the blanks below. ( example: the magnitude of the force in member...

Consider the cantilevered truss in Figure P 3 , which is supported by a pin at E and a roller at F . It is loaded with four point forces: F _ 1 = { 2 } kN , F _ 2 = { 3 } kN , F _ 3 = { 1 2 } kN ,...

k N , and F y = 7 7 . 0 k N , with the directions shown in the figure. Here h = 3 . 0 m and d = 3 . 0 m . Time left 3 : 3 2 Figure P 3 . Truss loaded with various point forces. a ) Determine the...

Consider the truss in Figure P 4 , which is supported by a rocker / roller at point A and a pin joint at point F . It is loaded with a vertical force P = { 4 5 0 } N and two angled forces Q = { 9 0 0...

Consider the roof truss shown in ( Figure 1 ) . Take P = 4 . 0 kN . Assume C is a pin and B is a roller support. Part A Determine the force in member A G of the roof truss. Indicate if the member is...

A regression of x = tannin concentration (mg/L) and y = perceived astringency score was considered in Examples 5.2 and 5.6. The perceived astringency was computed from expert tasters rating a wine on...

Which of the following parties influence whether a firm recognizes a goodwill impairment A. Managers B. Analysts C. Auditors D. All of the above E. Managers and Auditors Question 2: Managers only...

In a team meeting, Omar tells a colleague Are you joking? If you weren t such a newcomer, you d know that would never work. This represents Option A task conflict Option B relationship conflict...

The vertical shaft and attached clevis rotate about the z-axis at the constant rate = 4 rad/s. Simultaneously, the shaft B revolves about its axis OA at the constant rate w 0 = 3 rad/s, and the...

It is a simple matter to produce soap films that demonstrate thin-film interference phenomena. Place a few drops of liquid dish-washing detergent in a shallow bowl and add enough water to form a...

A 2018 Pew Research poll recorded respondents political affiliation and generation. A summary of the results for Millennials and GenXers are shown in the following table, assuming a sample size of...

The International Association of Accountants (IAA), a labor union, made a one-time donation to a political candidate who is also a member of the organization. In addition, the IAA publicly endorsed...

Derive the equation of motion for the system shown in terms of the displacement x. The masses are coupled through the light connecting rod ABC which pivots about the smooth bearing at point O....

Discuss what types of patterns are observed for the demand for clear containers: Is there a trend? If so, increasing or decreasing?

(x = - 3.3 MPa, (y = 8.9 MPa, Txy = - 14.1 MPa Using Mohr's circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on...

A post AB supporting equipment in a laboratory is tapered uniformly throughout its height H (see figure). The cross sections of the post are square, with dimensions b Ã b at the top and 1.5b...

Calculate the distance e from the centerline of the web of a C 15 x 40 channel section to the shear center S (see figure). (For purposes of analysis, consider the flanges to be rectangles with...

A 65-year-old male can purchase either of the following annuities from a life insurance company for $50,000. A 25-year term annuity will pay $307 at the end of each month. A life annuity will pay...

Rashid wants to use $500,000 from his RRSP to purchase an annuity that pays him $2000 at the end of each month for the first 10 years and $3000 per month thereafter. Global Insurance Co. will sell...

How much longer will it take month-end RRSP contributions of $500 to accumulate $500,000 than month-end contributions of $550? Assume that the RRSP earns 7.5% compounded monthly. Round the time...