Question: What is hoop stress?

What is hoop stress?

Step by Step Solution

★★★★★

3.47 Rating (154 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

The detailed answer for the above question is provided below Hoop stress also known as tangentia... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

Q:

____________urged Americans____________.

Q:

An A-36-steel hoop has an inner diameter of 23.99 in., thickness of 0.25 in., and width of 1 in. If it and the 24-in.-diameter rigid cylinder have a temperature of 65° F, determine the...

Q:

A standpipe in a water-supply system (see figure) is 12 ft in diameter and 6 inches thick. Two horizontal pipes carry water out of the standpipe; each is 2 ft in diameter and 1 inch thick. When the...

Q:

Please answer my doubts and derive the equation for b and d only (b) Derive the axisymmetric stress equilibrium equation in polar coordinates, and show that [3 marks) it can be written in the form a...

Q:

11.54 A reactor pressure vessel is usually clad in stainless steel to prevent corrosion and radiation embrittlement. Thus, the occurrence of subclad cracks is higher than that of surface cracks. Kim...

Q:

Calculate critical crack depth (the answer value must be correct (+15% error permitted) to get the mark) For a thick wall tube with a flaw of depth a under tensile hoop stress of a=690MPa due to the...

Q:

A steel pipeline is designed for a pressure, P , with a mean of 4 MN / m 2 and a coefficient of variation ( COV ) of 0 . 1 2 . It is considered in the design that the pipeline fails due to yielding...

Q:

Design of a high - temperature high - pressure processing vessel [ 1 5 0 Points Total ] In order to control bacterial growth and prevent food - borne illness, many food products ( especially liquid...

Q:

I have put 110,000 and it says wrong every time

Q:

SKILL DEVELOPMENT STUDY # 2 Due date: December 2 2 , 2 0 2 4 Material Specification for a Pressurized Cylindrical Tank Consider a thin - walled cylindrical tank of radius 0 . 5 m ( 5 0 0 m m ) and...

Q:

An object initially at rest at position x = 20 has acceleration a = 2. a. Find the velocity and position. b. When will the object reach position 100?

Q:

Assume you are a senior partner in an accounting firm and must prepare a report for a group of recruits who aspire to become auditors with your firm. Prepare a Report including detailed speaker notes...

Q:

A population of 4 2 0 bacteria is introduced into a culture and grows in number your answer to two decimal places. ) P ( t ) = 4 2 0 ( 1 2 t 2 0 t 2 ) P ' ( 4 ) = bacteria / hour

Q:

The unadjusted trial balance for Garden Designs at its year end, April 30, 2017, is as follows: Additional information: 1. $500 of the unearned revenue has been earned by April 30, 2017. 2. The...

Q:

To test H0: = 40 versus H1: 7 40, a simple random sample of size n = 25 is obtained from a population that is known to be normally distributed. (a) If x = 42.3 and s = 4.3, compute the test...

Q:

The following information, taken from the books of Theodore Co., represents the operations for January: The job cost system is used, and the February cost sheet for Job M45 shows the following: The...

Q:

To test H0: = 20 versus H1:

Q:

(a) Determine the critical value for a right-tailed test of a population mean at the = 0.01 level of signicance with 15 degrees of freedom. (b) Determine the critical value for a left-tailed test of...

Q:

If a partner would like to continue a partnership beyond the originally agreed-on term, the partner has ________blank.Multiple Choicean unconditional right to do sono right to continue without the...

Q:

= 2. (18 Points) Two strain gages are mounted on a 16 oz can of Red Bull (223 calories, 148 mg caffeine) with internal cylindrical dimensions of R 1.1875 in and height H=6.52 in. The wall thickness...

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

For the design of a thin-walled cylindrical pressure vessel, it was suggested to use a particular grade of steel with fracture toughness Kc = 35 MPa m/2 and yield strength oy = 960 MPa. The pressure...

Q:

Consider two long cylinders of two different materials where one cylinder just fits inside the other. The inner radius of the inner cylinder is a, and its outer radius is b. The inner radius of the...

Q:

( b ) . A simple thick cylinder of ID 7 5 m m and OD 1 9 0 m m is internally pressurised to 6 0 M N m 2 . ( i ) Find the hoop stress for this system predicted by thin cylinder theory. ( 8 marks ) (...