Question: Determine the vertical displacement at joint ¡ and the force in member ¤. Take A = 0.0015 m 2 and E = 200 GPa. 2

Determine the vertical displacement at joint ‘¡ and the force in member ‘¤.  Take A = 0.0015 m2and E = 200 GPa.

2 m 2 m- 4 10 2 m 4 30 kN

2 m 2 m- 4 10 2 m 4 30 kN

Step by Step Solution

★★★★★

3.25 Rating (160 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Here Then applying Q KD From the matrix partition Q k K 11 D u K 12 ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Structural Analysis Questions!

Q:

Determine the vertical displacement of joint A if members AB and BC experience a temperature increase of ÎT = 200 o F. Take A = 2 in 2 and E = 29 (10 3 ) ksi. Also, α = 6.60 (10...

Q:

Determine the vertical displacement of joint A. Assume the members are pin connected at their end points. Take A = in 2 and E = 29 (10 3 ) for each member. Using Castiglianos theorem. 8 ft AO B - 8...

Q:

Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional area of A = 300 mm 2 . E = 200. Using Castiglianos theorem. 3 m 4 m 4 m 4 m 3 kN 3 kN 4 kN

Q:

Determine the stiffness matrix K for the truss. Take A = 0 . 0 0 1 5 m 2 and E = 2 0 0 GPa for each member. Node 4 is pinned support and node 2 is roller support. PART B Determine the horizontal...

Q:

PART A Determine the stiffness matrix K for the truss. Take A = 0 . 0 0 1 5 m 2 and E = 2 0 0 GPa for each member. Node 4 is pinned support and node 2 is roller support. PART B Determine the...

Q:

Determine the vertical displacement of joint C. Assume the members are pin connected at their end points. Take A = 200 mm 2 and E = 200 GPa for each member. Use the method of virtual work. 4 m A E 4...

Q:

For the pin-connected truss shown below use the virtual work method to determine the vertical displacement of joint A if members AE and ED experience a temperature increase of ?T = 250?C. Assume both...

Q:

Determine the vertical displacement of node ¡ if member ¥was 10 mm too long before it was fitted into the truss. For the solution, remove the 20-k load. Take A = 0.0015 m 2 and E = 200 GPa...

Q:

Solve this using excel ( matrix structural analysis ) and show the steps Determine the vertical deflections at joint 2 and 4 , the internal forces in all members, and the reaction forces at supports...

Q:

Solve this problem using Excel for matrix structural analysis. Please show the steps and, most importantly, display the equations or commands you used in Excel. Determine the vertical deflections at...

Q:

Explain why the renewability feature makes term insurance more attractive to some buyers.

Q:

Thompson Manufacturing is considering two investment proposals. The first involves a quality improvement project, and the second is about an advertising campaign. The cash flows associated with each...

Q:

2 . Should Surf Rider allow its yen position to be unhedged? Discuss / Explain the tradeoff.

Q:

Nurcombe and Fitzhenry-Coor (1979) have argued that training in diagnostic techniques should lead a clinician to generate (and test) more hypotheses in coming to a decision about a case. Suppose we...

Q:

The plate clutch consists of a flat plate A that slides over the rotating shaft S. The shaft is fixed to the driving plate gear B. If the gear C, which is in mesh with B, is subjected to a torque M,...

Q:

The shaft of diameter b is held in the hole such that the normal pressure acting around the shaft varies linearly with its depth as shown. Determine the frictional torque that must be overcome to...

Q:

Because of wearing at the edges, the pivot bearing is subjected to a conical pressure distribution at its surface of contact. Determine the torque M required to overcome friction and turn the shaft,...

Q:

Key facts and assumptions concerning Kroger Company, at December 12, 2007, appear below. Using this information, answer the questions following. Facts and Assumptions Yield to maturity on long-term...

Q:

QUESTION 20 Ken Can Co. has the following tax information for this year: Pretax income $72,000 Taxes payable $12,000 Income tax expense $19,000 Income tax paid $11,000 The reported effective tax rate...

Q:

The Impact of Special Events: page 27. Please identify the specific financial risks that would be applicable to each special event, Commodity Price Increases, Competing Product Introduction and...