Question: The carbide tips of the cutting teeth of a circular saw are 8.6 cm from the axis of rotation. (a) The no-load speed of the

The carbide tips of the cutting teeth of a circular saw are 8.6 cm from the axis of rotation.
(a) The no-load speed of the saw, when it is not cutting anything, is 4800 rev/min. Why is its no-load power output negligible?
(b) While the saw is cutting lumber, its angular speed slows to 2400 rev /min and the power output is 1.9 bp. What is the tangential force that the wood exerts on the carbide tips?

Step by Step Solution

★★★★★

3.43 Rating (162 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

IDENTIFY Apply t FR and Ptw SET UP 1hp746 W z rads 30 revmin EXECUTE a With no ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

P-M-R-M (31).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

A tugboat exerts a 2.8-kN force along its axis on a barge at point B. Replace the force applied at B with an equivalent system formed by two parallel forces applied at A and C. 2 43

The cutting tool on the lathe exerts a force F on the shaft in the direction shown. Determine the moment of this force about the y axis of the shaft. Units Used: kN = 103 N Given: F = (6 -4 -7)kN a =...

The earth rotates on its axis at an angular speed of 1 rev/24 h. Find the linear speed (in km/h) (a) Of Singapore which is nearly on the equator. (b) Of Houston which is approximately 30.0 north...

What is the mean range of the following set of data? 25 28 29 33 35 27 24to. 25.5 c. 29.5

On Monday, April 5, 2010, just before 3:00 in the afternoon, miners at Massey Energy Corporation's Upper Big Branch coal mine in southern West Virginia were in the process of a routine shift change....

read case seven entitled "the Upper Big Branch Mine Disaster" at page 500 of your book and discuss the costs and benefits to stakeholder of the action taken by Massey Ebergy and its managers. The...

PROBLEM 1 . 6 0 pts The End Connector ( Fig . 1 ) is machined on a CNC system using carbide tools. Turning: 1 0 0 ft / / min cutting speed, feed 0 . 0 1 0 inch / rev Milling: 8 0 ft / / min cutting...

can u solve the red parts of the question, and at maximum 2 lines answer for each one Q-1 Describe the design-limiting properties for each of the following: (a) A cobalt chrome molybdenum alloy for...

What is the applicable Rule of Origin for Soya Sauce under the CUSMA Trade Agreement?

The Upper Big Branch Mine Disaster On Monday, April 5, 2010. just before 3:00 in the afternoon, miners at Massey Energy Corporation's Upper Big Branch coal mine in southern West Virginia were in the...

Look again at Problem 8.11, which concerns whether you should drop your decision analysis course. Estimate EVPI for your score in the course.

Since Jane Lee started work in your factory, she has kept to herself during breaks. Some of her male fellow employees have formed the impression that because she is female and speaks with an accent,...

The comparison universe is not: Multiple Choice 2 . 2 8 a set of mutual funds with different risk characteristics to your mutual fun the set of all mutual funds in the U . S . a concept found only in...

cot 70 + 4 cos 70 = /3 %3D

From 4 to subtraction. 15. asin0 + b cos0 = c 4R a coseco + b sec0 = c proves that sin26 2ab% 3D c2 - g2 - h2 15. asin0 + b cos0 = c 4R a coseco + b sec0 = c , sin26 2ab %3D c2 - g2 - h2

12. 2 sine sin20 2 sin 0 + sin 20 tan 2 %3D

Sim 1 10. Prove that 2 == V2 + V3. V2 -1 V3 +1 4,3

= tan 'a. log (x + y)+b tan), prove a'u, o'u ax Oy %3D

P12.8 (LO 2) (Premium Entries) To stimulate the sales of its Alladin breakfast cereal, Loptien NV places one coupon in each box. Five coupons are redeemable for a premium consisting of a childrens...

The following options have the same underlying stock that does not pay any dividends. The stock is currently trading at $20 per share. Rank the following options by price, starting with the highest...

I am most confused with the bonus than anything Philadelphia Fastener Corporation manufactures nails, screws, bolts, and other fasteners. Management is considering a proposal to acquire new...

Maris Brothers, Inc., needs a cash disbursement schedule for the months of April, May, and June. Use the format given here and the following information in its preparation. Sales: February $501,000;...