Question: The design floor elevation for a building to be constructed is 332.56 ft. An instrument is set up nearby, leveled, and a plus sight of

The design floor elevation for a building to be constructed is 332.56 ft. An instrument is set up nearby, leveled, and a plus sight of 6.37 ft taken on BM A whose elevation is 330.05 ft. If batter boards are placed exactly 1.00 ft above floor elevation, what rod readings are necessary on the batter board tops to set them properly?

Step by Step Solution

★★★★★

3.40 Rating (150 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

286 ft Stati... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

707-P-M-K (831).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

In the design of buildings, energy conservation requirements dictate that the exterior surface area, A" be minimized. This requirement implies that, for a desired floor space, there may be optimum...

A cold-storage building 16 35 m is built on a concrete slab having a thickness of 15 cm, which is placed on a suitable insulating material in contact with the ground. During the start-up period the...

Design the stormwater-collection pipes in Problem 11.8.13 given the following data changes. The upstream elevation for pipe AB is 23.9 ft instead of 24.9 ft, the inlet time for basin 1 is 14 min...

Grade stakes for a pipeline running between stations 0+00 and 6+37 are to be set at each full station. Elevations of the pipe invert must be 843.95 ft at station 0+00 and 847.22 ft at 6+37, with a...

2 3 . 1 1 Grade stakes for a pipeline running between stations 0 + 0 0 and 5 + 6 4 are to be set at each full station. Elevations of the pipe invert must be 1 6 0 . 8 5 ft at station 0 + 0 0 7 3 6...

@Ivay \\ Publishing W13355 SAWGHYN GUITARS: CAN AN lVZ'iLIII BUSINESS LEARN HEW TRICKS? Meredith Woodwark end Matthew Wig mots this cessI solely to provide metaoel'lbr arm .iacuaaion. The authors do...

Given the elevation of Point A on the baseline, determine the ground elevation of all the building points. For the assigned finished basement floor elevation of the building, compute the "cut" for...

Ccan u please showw all the hand sketches for a steel structural design for this plan which shows each floor elevation plan a , foundation and roof which could be a steel truss showing the load...

Advanced Project D 333 9. What service should be called before any excavation starts? 10. Give the distances the building is set back from the following locations. A. Vernon Place B. East University...

Owners of a new commercial, single story building are complaining about low water pressure inside the building. Your consulting firm has been hired by the municipality to determine if the owners have...

1. What facts would support Leonards primary argument as to why this commercial was a unilateral offer to contract? 2. If the languagein the catalog order form had allowed a consumer to write in the...

By reference to the extract below, elaborate on the constitutional development o during the period 1910 to 1993, local government Local government gives people a sense of involvement in the political...

Often a credit union's lending staff do not personally have to scan loan applicants against the SDN list. Why?

What is the role of a team charter in Resource Management? a) To define the project scope b) To outline the project schedule c) To establish team values, agreements, and operating guidelines d) To...

Locate the centroid of the section shown, which was cut from a thin circular pipe by two oblique planes. .d 3

Locate the centroid of the plane area shown. 6 in 6 in 6 in

Locate the centroid of the plane area shown. 120 mm r 75 mm

for(int i=0;i

Here are data on two companies. The T-bill rate is 5.4% and the market risk premium is 8.3%. Company $1 Discount Store Everything $5 Forecast return 16% 15% Standard deviation of returns 26% 28% Beta...

Walker Machine Tools has 7 million shares of common stock outstanding. The current market price of Walker common stock is $82 per share rights-on. The company's net income this year is $25.00...