Question: The extruder head in a fused-deposition-modeling setup has a diameter of 1 mm and produces layers that are 0.25 mm thick. If the velocities of

The extruder head in a fused-deposition-modeling setup has a diameter of 1 mm and produces layers that are 0.25 mm thick. If the velocities of the extruder head and polymer extrudate are both 50 mm/s, estimate the production time for generating a 50-mm solid cube. Assume that there is a 15-second delay between layers as the extruder head is moved over a wire brush (for cleaning)?

Step by Step Solution

★★★★★

3.40 Rating (162 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Side of the cube is 50 mm and thickness of the layers is 025 mm Therefore calculate the total number ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

972-E-M-E-B-D (959).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

A steel spur pinion has a module of 1 mm and 16 teeth cut on the 20 full-depth system and is to carry 0.15 kW at 400 rev/min. Determine a suitable face width based on an allowable bending stress of...

The rod has a diameter of 1 in. and a weight of 15 lb/ft. Determine the maximum torsional stress in the rod at a section located at B due to the rods weight. 4.5 ft -1.5 ft 1.5t B. 1.5 ft 4 ft

The rod has a diameter of 1 in. and a weight of 10 lb/ft. Determine the maximum torsional stress in the rod at a section located at A due to the rods weight. 4.5 ft 1.5 ft 1.5 ft B. 4 ft

A pentagonal tube is needed and must be prototyped using either SLA or MEX ( FFF ) . It will be 4 0 mm tall, with an outside cross section with an outside side length of 3 0 mm and has a 4 mm wall...

Problem 6 (15 points) We are using fused deposition modeling to create a cylindrical cup. Assume that the cup is 100 mm high, with an outside diameter of 90 mm and a wall thickness of 4 mm. The...

Question 1 The extruder head in a fused - deposition modelling machine has a diameter of 1 . 5 mm and produces layers that are 0 . 7 5 mm thick. Assume there is a 2 second delay between each layer...

do it carefully ASAP otherwise I will report. dohat. ELEMENT CORRUGATOR TABLE 1 - NUMBER OF FAULTS OR STOPS EXTRUDER HEAD MATERIAL SLICER TURNING AND TRANSPORT SYSTEM MOLD 25 GRAND TOTAL 25 1 1 6 0...

Can I get help analyze this case studie by indentifying causal factors and conducting situational analysis. What caused the defect? What allowed the defect to escape detection? What in the quality...

In a Fused Filament Deposition process (a type of MEX process) a thermoplastic filament of standard 1.75 mm diameter is fed into the extruder head at velocity, Vfeed, and the nozzle has a standard...

I need help to answer this questions using that article, with introduction, 3 body paragraphs and conclusion. Using 2 reference from books,journal/periodical articles. What cause the defect? What...

Assume that you have a sample of n1 = 8, with the sample mean X 1 = 42, and a sample standard deviation 1 = 4, and you have an independent sample of n 2 = 15 from another population with a sample...

Calculate the present value of the following singleamounts. Future Value $10,000 7,000 6,000 Annual Rate Interest Compounded Period Invested 1. 2. 6% Annually Semiannually Quarterly 5 years 8 years 4...

Question 6 4 pts Sally has $ 8 0 , 0 0 0 of wages in 2 0 2 3 . In addition, she has a business that generates $ 1 5 , 0 0 0 of gross income and has $ 2 0 , 0 0 0 of related expenses. Sally also had $...

2. Suppose that in a later market period, the quantities supplied in the table in Problem 1 are unchanged. The amount demanded, however, has increased by 30 million at each price. Construct the...

Repeat problem 2.72 if the flow inside the apparatus is liquid water, 1000 kg/m3, instead of air. Find the pressure difference between the two holes flush with the bottom of the channel. You cannot...

The main waterline into a tall building has a pressure of 600 kPa at 5 m elevation below ground level. How much extra pressure does a pump need to add to ensure a water line pressure of 200 kPa at...

A 5-kg piston in a cylinder with diameter of 100 mm is loaded with a linear spring and the outside atmospheric pressure of 100 kPa. The spring exerts no force on the piston when it is at the bottom...

The test statistic of z = 2.34 is obtained when testing the claim that p # 0.437. a. Identify the hypothesis test as being two-tailed, left-tailed, or right-tailed. b. Find the P-value c. Using a...

1. In computing the present and future value of multiple cash flows: A) each cash flow is discounted or compounded at the same rate. B) each cash flow is discounted or compounded at a different rate....

Year Cash Flow 0 $ 18,400 1 10,700 2 9,600 3 6,100 What is the profitability index for the set of cash flows if the relevant discount rate is 11 percent? (Do not round intermediate calculations and...