Question: The normal and shear stresses acting on element B are (x = - 46 MPa, (y = - 13 MPa, and Txy = 21 MPa

The normal and shear stresses acting on element B are (x = - 46 MPa, (y = - 13 MPa, and Txy = 21 MPa (see figure for Problem 7.2-8).
Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element?

Step by Step Solution

★★★★★

3.47 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

s x 46 MPa s y 13 MPa T xy 21 MPa s 1 28 MPa s ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

836-P-M-S (657).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

Solve the preceding problem if the normal and shear stresses acting on element B are 46 MPa, 13 MPa, and 21 MPa (in the directions shown in the figure) and the angle is 42.5° (clockwise). 13 MPa...

Solve the preceding problem if the normal and shear stresses acting on element A are 6500 psi, 18,500 psi, and 3800 psi (in the directions shown in the figure). Determine the stresses acting on an...

The normal and shear stresses acting on element A are 6500 psi, 18,500 psi, and 3800 psi (in the directions shown in the figure) (see the figure for Problem 7.2-5)? Determine the maximum shear...

The following problems are to be solved using Mohr's circle. Neatly and carefully, hand-generate Mohr's circle solutions so that the final solution is easy to identify and grade. Draw Mohr's circles...

Question 3 A simply supported A36 steel universal beam is subjected to a 30 kN point load as shown in Figure 3. You are required to: a) Calculate all the internal forces acting at the cross-section...

Develop a MATLAB code that is capable of the followings: a) Your code can interactively plot a Mohr's circle for a set of stresses (ox, oy, 0 Try. Txz. Tyz) in 3D by importing the Microsoft Excel...

Part 1 The beam shown is supported by a tie bar at B and by a pin connection at C . The beam span is L = 5 . 5 m , and the uniformly distributed load is w = 1 6 k N m . The tie bar at B has an...

A CASE STUDY OF TUNNEL INSTABILITY IN WEAKNESS ZONE CONTAINING SWELLING CLAY Dawei Mao1,2 Bjrn Nilsen Shurong Feng ? Haibin Zhao 2 Ming Lu14 1 Nanyang Technological University, Singapore PowerChina...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

The cantilever beam shown in the figure is subjected to a concentrated load at point B . The stresses acting at point H on the beam are to be determined. For this analysis, use the following values:...

By what factor is the probability in Prob. 9 decreases if the number of balls is doubled (4 blue, etc)?

The table shows GSS data on happiness and the number of close friends, with expected cell counts given underneath the observed counts. a. Suppose the variables were independent. Explain what this...

Monopolistic competition is said to be productively inefficient because (A) the long-run price is above minimum average total cost. (B) long-run profits are positive. (C) firms engage in collusive...

57. For a sample of students in a college studying Business Administration, the mean grade point average is 3.10, with a standard deviation of 0.25. Compute the coefficient of variation.

The engine of a helicopter is delivering 600 hp to the rotor shaft AB when the blade is rotating at 1200 rev min. Determine to the nearest 1/8 in.the diameter of the shaft AB if the allowable shear...

The engine of a helicopter is delivering 600 hp to the rotor shaft AB when the blade is rotating at 1200 rev/min. Determine to the nearest in. the diameter of the shaft AB if the allowable shear...

The assembly is made of A-36 steel and consists of a solid rod 20 mm in diameter fixed to the inside of a tube using a rigid disk at B. Determine the angle of twist at C. The tube has an outer...

43415 is incorrect. 434 is incorrect. Please show correct answer. The following table gives the pattern of investment year rates and portfolio rates over a period of time from 2005 up through 2010....

If the spot rate for Canadian dollars is 1.25 dollars equals 1 US $, and the annual interest rate on fixed rate one-year deposits of Canadian dollars is 2.5% and for US$ is 1.5%, what is the...

3. 0.25/1.25 points | Previous Answers LCalcCon5 6.4.013. My Notes Ask Your Teacher The willingness of saddle producers to supply saddles can be modeled as for p