Question: An S-shaped block used in force measurement as shown in Figure P11-17 is to be designed for a pressure of 1000 psi applied uniformly to

An S-shaped block used in force measurement as shown in Figure P11-17 is to be designed for a pressure of 1000 psi applied uniformly to the top surface. Determine the uniform thickness of the block needed such that the sensor is compressed no more than 0.05 in. Also make sure that the maximum stress from the maximum distortion energy failure theory is less than the yield strength of the material. Use a factor of safety of 1.5 on the stress only. The overall size of the block must fit in a 3-in.-high, 2-in.-wide, 2-in.-deep volume. The block should be made of steel.

Figure P11-17 S-shaped block

1000 psi 3 in. (uniform) -2 in. Fixed base

Step by Step Solution

★★★★★

3.44 Rating (160 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Allowable stress is 50 ksi FOS of 15 3333 ksi A thickness of ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

1414-P-T-H-T(1503).docx

120 KBs Word File

Students Have Also Explored These Related Thermodynamics Questions!

An electro-hydraulic positioning system is shown in Figure P11.38. Use the following values. K a = 10 V/A Ki = 10 2 in./V K 2 = 3 10 5 sec 3 K 3 = 20 V/in. z = 0.8 w n = 100 rad/sec t = 0.01 sec a....

(Multiple Choice) (1) A baseball player hits a ball with a bat. If the force with which the bat hits the ball is considered the action force, what is the reaction force? (a) The force the bat exerts...

An SPC chart is to be designed for a key process variable, a chemical composition, which is also a controlled variable. Because the measurements axe very noisy, they must be filtered before being...

A CASE STUDY OF TUNNEL INSTABILITY IN WEAKNESS ZONE CONTAINING SWELLING CLAY Dawei Mao1,2 Bjrn Nilsen Shurong Feng ? Haibin Zhao 2 Ming Lu14 1 Nanyang Technological University, Singapore PowerChina...

The dramatic journey of the crippled Apollo 13 vehicle has been heavily documented and popularized. Many people know there was an explosion in the service module which caused the vehicle to lose its...

Procedure I Data Table 1: Mass and Weight Object Mass in g Mass in kg Weight in N Wooden Friction block 31.1 0.031 0.30 Glass /sandpaper friction block 55.6 0.056 0.55 50 g hanging mass 50 0.05 0.49...

I've provided all the information, I would appreciate assistance with Question 5 and 6 as well as Graph 1 and 2 and Data Table 3 and 4. Thank you. Exercise 1 Measuring Static and Kinetic Friction In...

Friction EXPLORATION EXPERIMENTATION EVALUATION Exercise 1 Measuring Static and Kinetic Friction Need Help? In this exercise you will measure the forces and coefficients of static and kinetic...

The experimental result differs from the assumption. The result shows that the ring oscillator frequencies can be grouped into two groups, where the first group is the high frequency group for the...

What factors would you consider in deciding whether to use wide or narrow control limits for forecasts?

The balance sheet and the income statement of Omega Company containing data in is as follows: Balance Sheet 20X1 Assets Fixed assets: Due to significant changes to the financial environment in one...

14.30 In Problem 14.8 on page 513, you used land area of a property and age of a house to predict the fair market value (stored in Glen Cove ). Using the results from that problem, a. construct a 95%...

2.1 Describe how survey research is conducted.

A very long copper rod [k = 372 W/m C] 2.5 cm in diameter has one end maintained at 90C. The rod is exposed to a fluid whose temperature is 40C. The heat-transfer coefficient is 3.5 W/m2 C. How...

An aluminum fin 1.5 mm thick is placed on a circular tube with 2.7-cm OD. The fin is 6 mm long. The tube wall is maintained at 150C, the environment temperature is 15C, and the convection...

A straight fin of rectangular profile has a thermal conductivity of 14 W/m C, thickness of 2.0 mm, and length of 23 mm. The base of the fin is maintained at a temperature of 220C while the fin is...

2 Duela Dent is single and had $183,200 in taxable income. Use the rates from Table 23 (Do not round intermediate calculations and round your answer to 2 decimal places, e.g., 32.16.) Calculate her...

Researchers have wanted to investigate the relationship between physical activity and mental health. Below isan example of sample data for a study that looked at ten people who were measured on both...

5. Annual volatility for a particular company share is 32%. Assuming 256 days in a year, what is the daily volatility likely to be? 6. I am examining two investment strategies, both of which promise...