Question: For the same PLL of Problem 10.6, design a loop filter with a zero that gives a crossover frequency for the loop gain of 100

For the same PLL of Problem 10.6, design a loop filter with a zero that gives a crossover frequency for the loop gain of 100 rad/s. The loop phase shift at the loop crossover frequency should be −135◦.

Step by Step Solution

★★★★★

3.48 Rating (161 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

If w 2 the zero frequency is at the unity gain point then the loop phase sh... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (2 attachments)

1528_605d88e1c3e40_687053.pdf

180 KBs PDF File

1528_605d88e1c3e40_687053.docx

120 KBs Word File

Students Have Also Explored These Related Analysis and Design Integrated Circuits Questions!

Estimate the capture range of the PLL of Problem 10.7, assuming that it is not artificially limited by the VCO frequency range.

Design a problem to help other students better understand how to find outputs when given a transfer function and an input. A circuit is known to have its transfer function as Find its output when:...

Assuming the loop filter model for an imperfect second-order PLL described in the preceding problem, derive the steady-state phase errors under the three conditions of Î¸ 0 , f Î...

I need the MATLAB code for this problem and model if possible, please. V (s) PI kpwm 1/R 1 +ST, kr ke (a) 8.3 In designing the torque loop of Example 8.2, include the effect of the back-emf, shown in...

6. In Example 8.3 of your textbook, design the speed-loop controller, without the inner current loop, as shown in Figure 3, for the same crossover frequency and phase margin as in Example 8.3....

?This is the problem I need help with: These are the previous problems, already answered: A detailed solution to everything highlighted in yellow, including all work and MATLAB commands and plots,...

3. Supercavitating Vehicle Control Supercavitating vehicles can travel underwater at extremely high speeds. The increase in speed is accomplished through a dramatic reduction in drag on the vehicle...

Define the operational amplifier parameters (i) Slew rate (ii) Input bias current b) Draw wien bridge oscillator circuit using IC 741 c) List four specification of IC LM324 d) State the four...

Consider the PLL shown in Figure Q2. Assume that: i) the phase detector is a simple CMOS EXOR whose logic levels are ground and VDD = 5V, ii) both the input to the loop and the VCO output are square...

This is a desktop based activity focussing on deriving the characteristic equation of DC motor followed by obtaining the behaviour of system in time and frequency domains using computer simulation...

The IRS has established procedures to simplify taxpayers choice of entity for tax purposes. The procedures are referred to as the check-the-box regulations. Use the Internet to find articles or...

A scanning electron microscope is used to look at cell structure with 10-nm resolution. A beam of electrons from a hot filament is accelerated with a voltage of 12 kV and then focused to a small spot...

yes, calculate future projections for 2002, 2003, 2004, 2005 and 2006

5.3.9 Let X.t/ be a Poisson process of rate . Determine the cumulative distribution function of the gamma density as a sum of Poisson probabilities by first verifying and then using the identity Wr ...

A batch reactor converts component A into B, which in turn decomposes into C: where k 1 = k 10 e -E 1 RT and k 2 = k 20 e -E 2 RT . The concentrations of A and B are denoted by x 1 and x 2 ,...

A brewery has the capability of producing a range of beers by blending existing stocks. Two beers (suds and premium) are currently available, with alcohol concentrations (by volume) of 3.0% for suds...

For the transfer functions (a) Derive an analytical expression for the step response to a unit step change. Evaluate the step-response coefficients, {S i }, for a sampling period of Ît = 1. (b)...

In a random sample of 300 observations, the proportion of successes, found to be 40%. Determine the sample size necessary to estimate a population proportion to within 0.05 with 95% confidence.

Instructions: This assignment is related to your Chapter 5 (Salkind) material. It is not timed but assignment must be submitted by the specified due. Individual assignments that are not submitted...

XYZ is a retailer and sells 126,000 units per year. It purchases from a single supplier. Fixed cost per order is $840 and carrying cost is $12 per unit. Suppose XYZ orders 9,000 units per order from...