Use Fig 6 3 to specify suitable Schedule 40 pipe sizes for carrying the given volume fl ow rate of water in the suction line and in the discharge line of a pumped distribution system Select the pipe sizes both above and below the curve for the given fl ow rate and then calculate the actual velocity of flow in each Use Q 800 gal min DN (mm) NPS (in) 250 10 200 150 6 125 Suction lines 100 4 312 90 80 212 65 50 Discharge lines ' 32 25 4 20 15 1 2 6000 8000 10000 15 20 30 40 200 400 600 800 1000 2000 4000 60 80 100 10 Volume Flow Rate, Q (gal min) 15 6 8 10 60 Volume Flow Rate, Q (m h) 20 25 30 40 80 100 150 200 300 400 500600 800 1000 1200 2000 Schedule 40 Pipe Size

Question: Use Fig. 6.3 to specify suitable Schedule 40 pipe sizes for carrying the given volume fl ow rate of water in the suction line and

Use Fig. 6.3 to specify suitable Schedule 40 pipe sizes for carrying the given volume fl ow rate of water in the suction line and in the discharge line of a pumped system. Select the pipe sizes both above and below the curve for the given fl ow rate and then calculate the actual velocity of flow in each.

DN (mm) NPS (in) 250 10 200 150 6. 125 Suction lines 100 4 312 90 80 212 65 50 Discharge lines מ'ן 32 25 - З4 20 15 1

Use Q = 800 gal / min.

DN (mm) NPS (in) 250 10 200 150 6. 125 Suction lines 100 4 312 90 80 212 65 50 Discharge lines ' 32 25 - 4 20 15 1/2 6000 8000 10000 15 20 30 40 200 400 600 800 1000 2000 4000 60 80 100 10 Volume Flow Rate, Q (gal/min) 15 6 8 10 60 ++++ ++++ + Volume Flow Rate, Q (m/h) 20 25 30 40 80 100 150 200 300 400 500600 800 1000 1200 2000 ++++ ++++++ Schedule 40 Pipe Size

Step by Step Solution

★★★★★

3.55 Rating (162 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Q 800 galmin 1 ft 3 s449 galmin 1782 ft 3 s Suction pipe 5 i... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Applied Fluid Mechanics Questions!

The pipe flow in Fig P3.12 fills a cylindrical tank as shown. At time t = 0, the water depth in the tank is 30 cm. Estimate the time required to fill the remainder of the tank. D=75 cm 1 m V1-2.5 m/s...

The pipe flow in Fig P6.52 is driven by pressurized air in the tank. What gage pressure p1 is needed to provide a 20°C water flow rate Q = 60 m3/h? 30 m 0 Smooth pipeI d#5cm Open je 80 m 10 m In...

A small dam has a pipe carrying liquid water at 150 kPa, 20C with a flow rate of 2000 kg/s in a 0.5 m diameter pipe. The pipe runs to the bottom of the dam 15 m lower into a turbine with pipe...

Use Fig. 6.3 to specify suitable Schedule 40 pipe sizes for carrying the given volume fl ow rate of water in the suction line and in the discharge line of a pumped distribution system. Select the...

For the drying oil process shown in Appendix B.4, check and validate the design specifications for the following three pieces of equipment against the appropriate heuristics: P-501, H-501, V-501. Use...

Your final project task is to specify a suitable pump and determine operating conditions based on the information provided to you in the Course Project Part 1 and the information below. The pump will...

Instructions The specifications of the oil cooler with a bypass are given below. 3-in er Gate valve Heat exchanger K = 12 Globe valve 1-in- Gate valve Specifications: The total length of pipe in the...

Your final project task is to specify a suitable pump and determine operating conditions based on the information provided to you in the Course Proj Part 1 and the information below. The pump will...

identify z1 and z2 values by taking the pump level as the base line before start solving. what would be the elevations for the suction line z1 and the discharge line z2 and then solve the problem....

Question 2 Question 3 Question 4 The end. Question 1 [17 marks] a) If the temperature of the air on the ground is 12 C and the pressure is 760 mmHg? At what height above the earth is the pressure 300...

For the inventory system of Model 5-4, use OptQuest to look for the best (total-cost-minimizing) setting for ( s , S ). Let s run between 1 and 99 (by ones) and let S run between 2 and 100 (by ones);...

If an individual has a negative taxable income does that mean that he or she has an NOL? Explain.

MILESTONE VI: Chapter 2 4 Deliverables: A hedger takes a short position in five T - bill futures contracts at the price of Each contract is for $ 1 0 0 , 0 0 0 principal. When the position is...

Exercise 8.4.3 Why is it not optimal to exercise an American put immediately before an ex-dividend date?

Rank each set of alcohols below in order of increasing acidity. a. b. c. CI CI .CI CI CI CI

Draw resonance structures for each of the following anions. a. b. c.

In the reversible adiabatic expansion of 1.75 mol of an ideal gas from an initial temperature of 27.0C, the work done on the surroundings is 1300. J. If C V ,m = 3/2R, calculate q, w, U, and H.

Howell Petroleum, Inc., is trying to evaluate a generation project with the following cash flows: Year Cash Flow 0 $ 38,500,000 1 58,500,000 2 13,500,000 Compute the IRRs for this project. (Do not...

S&P Corp(SPC's) optimal capital structure consists of 40 percent debt and 60 percent equity. Given the following information, calculate the marginal cost of capital(MCC) schedule and the optimal...

The expected return on Big Time Toys is 1 2 percent and its standard deviation is 1 9 percent. The expected return on Chemical Industries is 9 percent and its standard deviation is 1 9 percent....