Use Fig 6 3 to specify suitable Schedule 40 pipe sizes for carrying the given volume fl ow rate of water in the suction line and in the discharge line of a pumped distribution system Select the pipe sizes both above and below the curve for the given fl ow rate and then calculate the actual velocity of flow in each Use Q 2000 gal min DN (mm) NPS (in) 250 10 200 150 6 125 Suction lines 100 4 312 90 80 212 65 50 Discharge lines ' 32 25 4 20 15 1 2 6000 8000 10000 15 20 30 40 200 400 600 800 1000 2000 4000 60 80 100 10 Volume Flow Rate, Q (gal min) 15 6 8 10 60 Volume Flow Rate, Q (m h) 20 25 30 40 80 100 150 200 300 400 500600 800 1000 1200 2000 Schedule 40 Pipe Size

Question: Use Fig. 6.3 to specify suitable Schedule 40 pipe sizes for carrying the given volume fl ow rate of water in the suction line and

Use Fig. 6.3 to specify suitable Schedule 40 pipe sizes for carrying the given volume fl ow rate of water in the suction line and in the discharge line of a pumped system. Select the pipe sizes both above and below the curve for the given fl ow rate and then calculate the actual velocity of flow in each.

DN (mm) NPS (in) 250 10 200 150 6. 125 Suction lines 100 4 312 90 80 212 65 50 Discharge lines מ'ן 32 25 - З4 20 15 1

Use Q = 2000 gal/min.

DN (mm) NPS (in) 250 10 200 150 6. 125 Suction lines 100 4 312 90 80 212 65 50 Discharge lines ' 32 25 - 4 20 15 1/2 6000 8000 10000 15 20 30 40 200 400 600 800 1000 2000 4000 60 80 100 10 Volume Flow Rate, Q (gal/min) 15 6 8 10 60 ++++ ++++ + Volume Flow Rate, Q (m/h) 20 25 30 40 80 100 150 200 300 400 500600 800 1000 1200 2000 ++++ ++++++ Schedule 40 Pipe Size

Step by Step Solution

★★★★★

3.32 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Q 2000 galmin 1 ft 3 s449 galmin 4454 ft 3 s Suction pipe 6 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Applied Fluid Mechanics Questions!

Water at 20°C is to be pumped through 2000 ft of pipe from reservoir 1 to 2 at a rate of 3 ft3/s, as shown in Fig P6.62, if the pipe is cast iron of diameter 6 in and the pump is 75 percent...

The pipe flow in Fig P3.12 fills a cylindrical tank as shown. At time t = 0, the water depth in the tank is 30 cm. Estimate the time required to fill the remainder of the tank. D=75 cm 1 m V1-2.5 m/s...

The pipe flow in Fig P6.52 is driven by pressurized air in the tank. What gage pressure p1 is needed to provide a 20°C water flow rate Q = 60 m3/h? 30 m 0 Smooth pipeI d#5cm Open je 80 m 10 m In...

For the drying oil process shown in Appendix B.4, check and validate the design specifications for the following three pieces of equipment against the appropriate heuristics: P-501, H-501, V-501. Use...

Your final project task is to specify a suitable pump and determine operating conditions based on the information provided to you in the Course Project Part 1 and the information below. The pump will...

Instructions The specifications of the oil cooler with a bypass are given below. 3-in er Gate valve Heat exchanger K = 12 Globe valve 1-in- Gate valve Specifications: The total length of pipe in the...

Your final project task is to specify a suitable pump and determine operating conditions based on the information provided to you in the Course Proj Part 1 and the information below. The pump will...

identify z1 and z2 values by taking the pump level as the base line before start solving. what would be the elevations for the suction line z1 and the discharge line z2 and then solve the problem....

Question 2 Question 3 Question 4 The end. Question 1 [17 marks] a) If the temperature of the air on the ground is 12 C and the pressure is 760 mmHg? At what height above the earth is the pressure 300...

Hl for A and B is 7.530 m ktotal=10.374 Pb=7.52662656*10^3 kg/m2 Brine at 160F (SG=1.04, m=10^-3 Pa*s) is drawn at a minimum rate of 250 gal/min from a tank into the 4-in suction line of the pump....

What is the difference between snapshot and eye pattern techniques in terms of how to trigger the oscilloscope and the required length of sequence?

Can a set of indifference curves be upward sloping? If so, what would this tell you about the two goods?

On June 2 9 , a multinational firm with British subsidiary decides it will need to transfer 1 0 million ( 1 0 million British pounds ) from an account in London to an account with a New York bank....

Exercise 8.4.2 Prove that if at all times before expiration the PV of the interest from the strike price exceeds the PV of future dividends before the expiration date, the call should not be...

For a given set of conditions, the fugacity of a gas is greater than the pressure. What does this tell you about the interaction between the molecules of the gas?

Predict the major product of the reaction between 1-butanol and: (a) PBr 3 (b) SOCl 2 , py (c) HCl, ZnCl 2 (d) H 2 SO 4 , heat (e) PCC, CH 2 Cl 2 (f ) Na 2 Cr 2 O 7 , H 2 SO 4 , H 2 O (g) Li (h) NaH...

What can you conclude about the ratio of fugacity to pressure for N 2 ,H 2 , and NH 3 at 500 bar using the data in Figure 7.10? Figure 7.10 1.5 H2, 1.4 N2 1.3 1.2 1.1 1.0 100 200 300 400 500 600 700...

a. Using this information, compute the March 31 (1) deposits in transit and (2) checks outstanding. Deposits in transit $ Checks outstanding b. Prepare a bank reconciliation for March. - Note: Use...

16. An annual report contains a great many statements and reports. Which one of the following statements/reports is not covered either by statute or by accounting standards? Ariedis way Bcash flow me...

can you show how you got the answer You are considering making a movie. The movie is expected to cost $10.3 million up front and take a year to produce. After that, it is expected to make $4.4...