Question: Why is there more improvement in steady-state error if a PI controller is used instead of a lag network?

Why is there more improvement in steady-state error if a PI controller is used instead of a lag network?

Step by Step Solution

★★★★★

3.44 Rating (167 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

If both the gain margin GM and the phase margin PM are positive then the control system is stable ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Control Systems Engineering Questions!

Q:

Why is there more concern about melting polar ice caps than about melting icebergs?

Q:

Why is there more carbon-14 in living bones than in once-living ancient bones of the same mass?

Q:

A PI controller is to be used in a temperature control system for a bioreactor. For nominal conditions, it has been determined that the closed-loop system is stable when 1 = 10 min and 10

Q:

Question 2 [ 2 0 Marks ] ( a ) Given the system of Figure 2 . 1 ( i ) Design the value of K 1 , as well as a in the feedback path of the minor loop, to yield a settling time of 4 seconds with 5 %...

Q:

The objective of this project is to design a controller Ge(s) for a given plant with transfer function: G, (s) = s(s+5)(s+10) For this project, the plant is Rotor winder shown in figure. The...

Q:

Question 1 [ 2 0 Marks ] ( a ) Consider the unity feedback system shown in Figure 1 . 1 G ( s ) = K ( s + 5 ) 3 ( i ) Find the location of the dominant poles to yield a 1 . 2 second settling time and...

Q:

A feedback control system with a PI (proportional+integral) controller is shown in the Figure. (a) Evaluate the Controller parameters (K and K;) so that its step response will have percentage of...

Q:

an engine to be G(s)=(s+0.5)(s+1)1 design a control system to regulate the output of the engine such that - the settling time is less than 2 seconds, - the maximum overshoot is less than 20%, and -...

Q:

You have learnt the purpose of implementing compensators or controllers in the control loop to achieve certain performance criteria. The types of compensators discussed were the PI, PD, PID, phase...

Q:

Task 1: Multiple production lines exist in a water bottling factory. The most automated part is the filling line, where plastic bottles are placed on a conveyor belt and driven towards a filling...

Q:

What is a transfer price? Under what conditions is a market based transfer price most likely to be used?

Q:

Why does competitive equilibrium pricing and output lead to a maximization of these surpluses?

Q:

. Suppose Dutton shareholders will agree to a merger price of $ 3 1 . 2 5 per share. Should Elgin proceed with the merger?

Q:

4. Go through the list of data warehousing risks described in this chapter and find two examples of each in practice.

Q:

A 2.0 inch diameter carbon steel shaft is to be turned on a lathe at 500. RPM with a 0.20 inch depth of cut and a feed of 0.030 in/rev. What is the minimum horsepower and torque that the lathe must...

Q:

Suppose the material used in Example 15.3 was an aluminum alloy and the drill rotational speed was 500. RPM. Recalculate the material removal rate, the power required, and the torque on the drill.

Q:

A drill press with a 0.375 inch diameter drill bit is running at 300. RPM with a feed of 0.010 in/rev. What is the material removal rate?

Q:

Payback, NPV, and IRR Rieger International is evaluating the feasibility of investing $94,000 in a piece of equipment that has a 5-year life. The firm has estimated the cash inflows associated with...

Q:

VA Math 2023: Section 3.2 - Math 20 x Course Hero + X - > C D webassign.net/web/Student/Assignment-Responses/submit?dep=27094153&tags=autosave#question4738395_3 Q x e i : Apps * Bookmarks SiriusXM...

Q:

The question is: approximately what is the range (interval from minimum to maximum value) in percentage of persons who use public transportation (panel g) with high proportions of positive tests...