Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure P12 6, allowing a factor of safety of 3 Use K 1 5 K o and ' 0 65 ' in computing the shaft load Use Meyerhofs method for computing the point load Figure P12 6 Sand y 17 0 kN m d' 31 8 m Sand 10 m Ysat 19 0 kN m3 o' 33

Question: Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure P12.6, allowing a factor of safety of

Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure P12.6, allowing a factor of safety of 3. Use K = 1.5 K_o and δ' = 0.65ϕ' in computing the shaft load. Use Meyerhof’s method for computing the point load.

Figure P12.6

Sand y = 17.0 kN/m d' = 31° 8 m Sand 10 m Ysat = 19.0 kN/m3 o' = 33°

Sand y = 17.0 kN/m d' = 31 8 m Sand 10 m Ysat = 19.0 kN/m3 o' = 33

Step by Step Solution

★★★★★

3.27 Rating (176 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Show the cross section of the pile as in Figure 1 Calculate the value of for the upper layer Here is the soil friction angle in the upper layer of sand and is the value of for the upper layer Substitu... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Principles Foundation Engineering Questions!

Figure P13.1 shows a drilled shaft in sand. Determine the maximum load that can be allowed on it. Assume ' = 0.6' and allow a factor of safety of 4. Use Berezantzev et al.s Eq. (13.18) for computing...

Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the a method and Table 12.11 for determining the skin friction and...

Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of...

1 8 . 6 Determine the maximum load that can be allowed on a 4 5 0 mm diameter driven pile shown in Figure 1 8 . 3 4 , allowing a safety factor of 3 . Use K = 1 . 5 K o and ' = 0 . 6 5 ' . FIG. 1 8 ....

? ? 12.9 Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the a method and Table 12.11 for determining the skin...

Thank you for your help, please answer all 3 parts of the assignment with work shown. For the driven pile shown in the soil profile below: Reinforced Concrete Pile: Square, side lengths = 1 f t...

Question 1 The frame supports the point load P at point C. The pins at A and B have diameters of 50 mm and 64 mm respectively. Pin A is in single shear, while Pin B is in double shear, and both pins...

1 2 . 3 6 Figure P 1 2 . 3 6 shows a 3 5 pile group consisting of 1 5 concrete piles of 4 0 0 mm diameter and 1 2 m in length. What would be the maximum load that can be allowed on the mat with a...

Produce a work breakdown structure for the minor dwelling project plan ( the image files provided) using ms word or another software. The work breakdown structure should have 4 hierarchy levels with...

U.S. Department of Transportation Federal Aviation Administration Subject: RUNWAY LENGTH REQUIREMENTS FOR AIRPORT DESIGN Advisory Circular Date: 7/1/2005 Initiated by: AAS-100 AC No: 150/5325-4B...

The following 3-stage amplifier has 2 inputs, V 0.5V and V2 = 2V. Assume the supply voltage for all Op Amps is + 5V-DC. a) Calculate voltage V, at the output of amplifier A b) Calculate currents i,...

Consider a particle of mass m moving freely in a conservative force field whose potential function is U. Find the Hamiltonian function, and show that the canonical equations of motion reduce to...

a Copy each diagram and rotate the shape using the given information. Do not use tracing paper. b Use tracing paper to check your answers to part a. i ii === 5- 4 +32- 2- 2 3 4 5 x 0- 0 1 2 3 4 5 x...

What is the purpose of a supply chain map?

Structural steel and stainless steel are both primarily made of iron. Why doesnt stainless steel rust? Research the issue and prepare an approximately 250-word report describing the reason. Cite at...

Recent technological advances have allowed for the production of graphene, which is a sheet of carbon atoms one atom thick, densely packed into a honeycomb structure. This material has excellent...

A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel (Figure P5.28). Two rivets, one in front and one in back, secure the ends of each step. The rivets...

Novelty Gifts, Inc. is experiencing some inventory control problems. The manager, Wanda LaRue, currently orders 5,000 units four times each year to handle annual demand of 20,000 units. Each order...

[The information presented here applies to questions 1, 2, and 3] Edie wants to borrow $325,000 to purchase a new condominium in New York. What are her monthly payments for a fully amortizing 30-year...

Aguilera Acoustics, Inc. (AAI), projects unit sales for a new seven-octave voice emulation implant as follows: Year Unit Sales 1 93,000 2 105,000 3 128,000 4 134,000 5 87,000 Production of the...