Question: For the same material and member as in Prob. 11.37, the initial crack length is a i = 0.5 mm, and the load history is

For the same material and member as in Prob. 11.37, the initial crack length is a_i= 0.5 mm, and the load history is replaced by repeated applications of the sequence shown in Fig. P11.52. Estimate the number of repetitions to failure.

MW-WM time one repettion Figure P11.52 M. Moment, N-m

Step by Step Solution

★★★★★

3.45 Rating (152 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Express the maximum nominal stress Here shaft radius is thickness is t and maximum bending moment is Substitute for 12 mm for t and 60 mm for b step 2 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Physics Questions!

For the same material and thickness as in Problem 7.66, estimate the force required for deep drawing with a blank diameter of 10 in. and a punch diameter of 9 in.

Two solid rods are made of the same material and have the same cross-sectional areas, and their lengths differ by a factor of two. If a compressive force F is applied to both, what is the ratio of...

Two cylindrical resistors are made from the same material and have the same length. When connected across the same battery, one dissipates twice as much power as the other. How do their diameters...

A policy maker in the Occupational Safety and Health Administration is under pressure from industry to permit the use of certain chemicals in a newly developed industrial process. Two different...

A thin electrical heater dissipating 4000 W/m 2 is sandwiched between two 25-mm-thick plates whose exposed surfaces experience convection with a fluid for which Too = 20C and h = 400 W/m 2 . K. The...

Lindsay Kay approached her friend Michael Wait about going into business together as co owners of a gardening centre. Lindsay loved gardening and had some skills as an accountant. Michael was a...

On December 31, Year 1, RAV Company purchased 60% of the outstanding common shares of ENS Company for $780,000. On that date, ENS had common shares of $500,000 and retained earnings of $120,000. In...

Vulcan Manufacturing Limited (VML) is a Canadian-based multinational plastics firm, with subsidiaries in several foreign countries and worldwide consolidated total assets of $500 million. VML's...

Two alternative designs are under consideration for a tapered fastening pin. The fastening pins are sold for $0.70 each. Either design will serve equally well and will involve the same material and...

Assume that it is January 1, 2019, and that the Mendoza Company is considering the replacement of a machine that has been used for the past 3 years in a special project for the company. This project...

A company purchased land and building from a seller for $900,000. A separate appraisal reveals the fair value of the land to be $200,000 and the fair value of the building to be $800,000. For what...

ANALYSIS OF ACTIVITY MEASURES Based on the financial statement data in Exercise 24-1A, compute the following activity measures for 20-2 (round all calculations to two decimal places): (a) Accounts...

Wrap Ltd. is a Canadian-controlled private corporation (CCPC). At the end of 20X5 , Wrap had the following tax account balances : Non-capital losses: $8,000 Net capital losses (incurred in 20X3):...

1. Outline an internal control program that could be installed that would prevent or at least disclose irregularities such as those identified in this case. 2. Outline an internal audit program that...

Carmel Fisheries operates both a fleet of fishing boats and a cannery. All fish brought in by the companys fleet are processed at its own cannery, and its cannery processes no other fish. If the...

Lark Enterprises Inc. is a personal holding company. From the information below, compute its maximum dividends-paid deduction. a. Land with a basis of $10,000 and a value of $50,000 was distributed...

On January 1, 2016, Knorr Corporation issued $700,000 of 6%, 5-year bonds dated January 1, 2016. The bonds pay interest annually on December 31. The bonds were issued to yield 7%. Bond issue costs...

Financial Statements of Peter Ltd. and its 80%-owned subsidiary Sam Ltd. as at December 31, Year 5, are presented below: Statement of Financial Position as at December 31 Year 5 Peter Ltd Sam Ltd...

On weekend evenings, customers arrive at the Showcase SuperLux (movie theater) at an average rate of 180 per hour. On average, there are 14 customers waiting in line to purchase tickets. After...

Data Warehousing Failures Eight studies of data warehousing failures are presented. They were written based on interviews with people who were associated with the projects. The extent of the failure...

Companies can intentionally commoditize their products or services as a strategy to make money. Discuss using these two different cases below how companies can intentionally commoditize their...

Adams, Inc. Armstrong, MA Adams, Inc. designs and manufacturers coated fabrics for the automobile, luggage, and furniture industries. Adams provides fabrics that cover interior panels and seats of...

Comprehensive Piedmont Manufacturing produces metal products with the following standard quantity and cost information: Direct Material Aluminum 4 sheets @ $4 $16 Copper 3 sheets @ $8 24 Direct labor...

Read these Instructions carefully! For October 2021, TruBent Machining's manufacturing activities generated the records shown in the Data sheet. TruBent worked on numerous Jobs that month and each...

Please answer question 1-22 A 3 C D E F G WINE Read these Instructions carefully! For October 2020, TruBent Machining's manufacturing activities generated 4 the records shown in the Data sheet....