Question: What would the ip address commands be for each interface? For example, Branch1(config)# ip address 192.168.1.1 255.255.255.0 Also what would the ip addresses be for

What would the ip address commands be for each interface? For

What would the ip address commands be for each interface? For example, Branch1(config)# ip address 192.168.1.1 255.255.255.0

Also what would the ip addresses be for the PC's so I can set that up too?

Thanks

.10 PC-B 10.10.2.0/24 Giol.1 ISP DCE so/0/1 so/0/0 .2 192.168.1.0/24 192.168.2.0/24 DCE S0/0/0 .1 so/0/1 Branch1 Gi01L1 Branch2 Gio |1 10.10.3.0/24 10.10.1.0/24 PC-C PC-A .10 .10

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

please help: Download the file telnet to other network pkt and perform the following operation. The two network has the same configuration from the one we used in class. You need to set up each of...

by using Packet Tracer Packet Tracer - Basic Switch and End Device Configuration Addressing Table Device Interface IP Address Subnet Mask Class A VLAN 1 128.107.20.10 255.255.255.0 Class-B VLAN 1...

by using Packet Tracer please solve this question Packet Tracer - Basic Switch and End Device Configuration Addressing Table Device Interface IP Address Subnet Mask Class A VLAN 1 128.107.20.10...

Securing Network Devices (Advanced) Obiective / Purpose This tab is a continuation from lab 1 (Besic device security). In this tab, students will configure secure access to devices via SSH on the VTY...

Configure the hostnames of routers according to the following format R 1 _ studentID and R 2 _ studentID. Configure the IP addresses as shown in the diagram below. Subnet mask should be 2 5 5 . 2 5 5...

CISCO CCNA Exploration LAN Switching and Wireless: Basic Switch Concepts and Configuration Lab 2.5.1: Basic Switch Configuration Cisco Networking Academy Mind Wide Open Lab 2.5.1: Basic Switch...

I need help with Capstone Project 8-2 Add VLANs to Your Packet Tracer Network from book CompTIA Network Guide to Networks (Cengage) 1. In Packet Tracer, open your Packet Tracer file from Capstone...

172.16.12.1 Fa 0/0 Fa 0/1Internet R1 172.16.12.2 192.122.237.7 In the above network, router R1 has been successfully configured with the following commands: R1 (config)# access-list 10 permit...

The two network has the same configuration from the one we used in class. Instructions You need to set up each of the four switches to enable Telnet or SSH . For Switch 1 , configure all 1 6 vty...

Packet Tracer 2.9.1 I'm almost at 100%. The only two I'm missing is both 'subnet mask' and I can't figure out what to do anywhere. It's not in the steps and again when I Google I find stuff that...

You purchased 400 shares of common stock on margin at $45 per share and sold them 9 months later at $65. Assume the margin requirement is 80%, interest rate on margin used is 3%, and the commission...

If the yield curve is downward sloping, what is the yield to maturity on a 30 year treasury bond relative to a 10 year treasury bond?

Jean recently retired at age 6 0 . A passionate art collector for some 3 0 years, Jean ton ten a mperan clacia. of Canadian paintings. His collection, which he acquired at a cost of $ 1 5 0 , 0 0 ,...

Seved Help 14 Wisconsin Snowmobile Corp. is considering a switch to level production Cost efficiencies would occur under level production, and aftertax costs would decline by $31,500, but inventory...

What are the Variable columns settings available in the Mining Models Tab?

What does the Mining Content Viewer in Visual Studio show in terms of Probabilities?

How are continuous variables normally handled in Decision Tree Algorithms?