Question: Write a program in C + + that lights a green LED attached to pin 3 . The green LED should turn off after a

Write a program in C++ that lights a green LED attached to pin 3. The green LED should turn off after a button attached to pin4 has been pushed and released 3 times. Each time the button is pushed it will turn on a red LED attached to pin 7 and turn off a yellow LED attached to pin 9. When the button is not pushed the red LED will be off and the yellow LED will turn on. Assume the button is wired active low.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

Solved: Lab 1-Lab Portion Par + X u/pluginfile.php/5346892/course/section/1891746/Lab % 20 % 231 %20- %201ntro % 2C % 20GPIO % 2C % 20LED % 2C % 20PW UNTYENOTTT Lab #1 -Introduction to the Arduino;...

Q:

2. Using a protoboard, connect an LED to pin RB1 on your PIC-WEB board. Be sure to use a current limiting resistor (470) in series with the LED (see attached PIC-WEB schematic, for proper wiring of...

Q:

Write a program in C++ that controls the stoplights of an intersection. The intersection is at a junction between two 2-lane roads. This light should be symmetric, meaning what is happening at the...

Q:

Question 2 (40 points) Write a C program to do the following: - . A green LED is blinking (on 1 second, off 1 second) Every time a magnet is detected, the blinking becomes slower (on 2 seconds off 2...

Q:

Goal: Add push button controls to your Circuit Project 2. Required: Circuit project 2 1 Push buttons 1-3 Resistors 1-3 Jump wires many Cook Manual Note: If you implemented the extra LED requirement...

Q:

needing a small abstract from the Arduino lab below 1 Program Syntax When you write a program in C, before it can be executed by the microcontroller, it needs to be translated into what is called...

Q:

For Arduino Uno: a. write a program that starts with a led on that is attached to pin 3. A push button is wired active low to pin 6. When the button is pushed the led light goes out. When the button...

Q:

Write a program in C that follows steps 5 and 7-11. Thank you. y to labz. iCliek on blinky and then e 6. Strip out all the blinky code and update the include directives to have these header files...

Q:

Write a program that lights a green LED attached to pin 3 . The green LED should turn off after a button attached to pin 4 has been pushed and released 3 times. Each time the button is pushed it will...

Q:

Level 1: Run the following code to make sure your button works. int blueLedPin = 13 ; //The blue LED is connected pin 13 of the Arduino. int button1Pin = 2; //The SW1 button is connect to pin 2 of...

Q:

If an erect object is placed at a distance So = 40 cm in front of an optical system as shown in Fig. P.5.26, find the image distance from the other end of the system (radius of curvature of all lens...

Q:

Pickens Corporation declares and issues a 10% stock dividend. On the date of declaration, the stock is selling for $30 per share. Assuming that there were 50,000 shares previously outstanding, with a...

Q:

In considering the wealth gap, the most important source of net worth for the typical middle - class family in America is: Question 1 0 options: the gift of money from Uncle Bob their retirement fund...

Q:

2. On January 1, Fox Co. issued $100,000 of ten-year, 10% bondsthat pay interest semiannually on June 30 and 31st. The bonds aresold to yield 8%.a. Using the information provided in this problem, a 0...