Question: Write a program that lights a green LED attached to pin 3 . The green LED should turn off after a button attached to pin

Write a program that lights a green LED attached
to pin 3. The green LED should turn off after a
button attached to pin4 has been pushed and
released 3 times. Each time the button is pushed
it will turn on a red LED attached to pin 7 and
turn off a yellow LED attached to pin 9. When
the button is not pushed the red LED will be off
and the yellow LED will turn on. Assume the
button is wired active low.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

Solved: Lab 1-Lab Portion Par + X u/pluginfile.php/5346892/course/section/1891746/Lab % 20 % 231 %20- %201ntro % 2C % 20GPIO % 2C % 20LED % 2C % 20PW UNTYENOTTT Lab #1 -Introduction to the Arduino;...

Q:

For Arduino Uno: a. write a program that starts with a led on that is attached to pin 3. A push button is wired active low to pin 6. When the button is pushed the led light goes out. When the button...

Q:

Using Tinkercad Circuits, wire up an Arduino Uno and write the program that starts with a led on that is attached to pin 3. A push button is wired active low to pin 6. When the button is pushed the...

Q:

You have AVR ATmega 16 microcontroller, one yellow LED and one bicolor LED. Write a program to make the bicolor LED start out red for 3 seconds (connected at I/O pin PB0 ). After 3 seconds, change...

Q:

/ / Hardware: One button with GPIO pullup resistor. / / One Green LED with 3 3 0 Ohm resistors. / / One Red LED with 3 3 0 Ohm resistors. / / The LCD with variable resistor to control brightness of...

Q:

Level 1: Run the following code to make sure your button works. int blueLedPin = 13 ; //The blue LED is connected pin 13 of the Arduino. int button1Pin = 2; //The SW1 button is connect to pin 2 of...

Q:

Can someone help me find the, State Diagram, State transition table and Excitations Table using JK and D flip-flops? If possible, the K-maps and Design. I know we use 3 bits and there are 3 inputs...

Q:

FOR COPY AND PASTE int sensorPin = 0; // select the analog input pin for the photoresistor int bPin = 9; // select the digital output pin for blue LED int gPin = 10; // select the digital output pin...

Q:

C CODE LANGUAGE. MSP430. #include #define redLED BIT0 // Red LED at P1.0 #define greenLED BIT7 // Green LED at P9.7 #define BUT1 BIT1 // Button S1 at P1.1 #define BUT2 BIT2 // Button S2 at P1.2 void...

Q:

Ok, let's redo some previous assignments to blink some LEDs but using Functions in C. For this assignment, we want to accomplish similar tasks but we want our main function to only call other...

Q:

You need to research a life of a political woman Adrienne Cecile Rich Explore her past and present of her issues she faced in her life to due to the workings of privilege and inequality. There are...

Q:

Zavala Manufacturing Company is a small family-owned business that makes specialty plastic products. Since it was started three years ago, the company has grown quickly and now employs ten production...

Q:

when calculating basic earnings per share, an income is reduced by dividends or non - convertible, cumulative preferred stock, whether declared or not only declared whether diluted or not under no...

Q:

Prance, Inc., earned pretax book net income of $1,997,000 in2020. Prance acquires a depreciable asset that year, and first-yeartax depreciation exceeds book depreciation by $199,700. Prancereported 2...