Question: Determine the structure stiffness matrix K for the frame. Assume is pinned and is fixed. Take E = 200 MPa, I = 300(10 6 )

Determine the structure stiffness matrixKfor the frame. Assume ž‚ is pinned and ‘ is fixed. Take E = 200 MPa, I = 300(10⁶) mm⁴, A = 21(10³) mm²for each member.

5 m- 300 kN · m, (2. (3 -5

5 m- 300 kN m, (2. (3 -5

Step by Step Solution

★★★★★

3.52 Rating (172 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

For member 1 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (2 attachments)

1589_60619c5b081ae_678346.pdf

180 KBs PDF File

1589_60619c5b081ae_678346.docx

120 KBs Word File

Students Have Also Explored These Related Structural Analysis Questions!

Determine the structure stiffness matrix K for the frame. Take E = 29(10 3 ) ksi, I = 700 in 4 , A = 20 in 2 for each member. 6. 2 16 ft 20 k - 12 ft- 3. 12 ft

Determine the structure stiffness matrix K for the frame. Assume and are fixed. Take E = 200 GPa, I = 300(10 6 ) mm 4 , A = 10(10 3 ) mm 2 for each member. 12 kN/m 1) 2 m - 4 m- 10 kN 2 m 6. (3'

Determine the structure stiffness matrix K for the frame. Take E = GPa, I = 350(10 6 ) mm 4 , A = 15(10 3 ) mm 2 for each member. Joints at and are pins. 2 60 kN 3 |1 2) 2 m - - 2 m 2 4 m

Determine the structure stiffness matrix K for the frame. Take E = 2 9 ( 1 0 3 ) k s i , I = 6 0 0 i n 4 , A = 1 7 i n 2 for each member. Assume joints ( 1 ) and ( 3 ) are pinned; joint ( 2 ) is...

Q . 7 Determine the structure stiffness matrix K for the frame and the support reaction at the fixed support 1 and 3 . Assume 1 and 3 are fixed. Take E = 2 0 0 GPa, I = 3 0 0 ( 1 0 6 ) m m 4 A = 1 0...

Part A Enter all the elements of submatrix M 1 in the correct order separated by commas. Express your answers using three significant figures separated by commas. View Available Hint ( s ) Part B...

For the shown frame, use the stiffness matrix analysis to determine: (a) The displacements vector D (show the known and unknown DOFs). (b) The loads vector Q (show the known and unknown forces). (c)...

Note: G40.21M-350W (Fy =350 MPa, Fu = 450 MPa) steel is to be used, unless otherwise specified. None of the beams in this assignment are cambered. It is not permitted to use M, values obtained from...

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 \ deg C to 3 0 \ deg C . Assume...

Dr. Tarun Gupta, a Michigan vet, is running a rabies vaccination clinic for dogs at the local grade school. Tarun can shoot a dog every 3 minutes. It is estimated that the dogs will arrive...

Let the regression model be linear Yi = a + Bx; + u, where y, is normally distributed with mean u = 2 and unit variance, x, exponential with 2 = 1 and sample size n= 200 Calculate: a) The estimator ...

1. Li Ting standing at P. is flying a kite attached to a string of length 140 m. The angle of elevation of the kite K from her hand is 58, Assuming that the string is taut, determine the vertical...

Use the data set Mireault.dat from Mireault (1990), described in the Appendix and found on the Web site for this book, to examine the relationship between current levels of depression and other...

Determine the location (xc, yc) of the center of gravity of the homogeneous wire bent in the form of a triangle. Neglect any slight bends at the corners. If the wire is suspended using a thread T...

The three members of the frame each have weight density . Locate the position (xc, yc) of the center of gravity. Neglect the size of the pins at the joints and the thickness of the members. Also,...

Locate the center of gravity G(xc, yc) of the streetlight. Neglect the thickness of each segment. The mass per unit length of each segment is given. Given: a = 1 m = AB 12kg/m b = 3 m = BC 8kg/m c...

a. How to solve for the current price of the bonds b. How to find the percentage at which the price of the bonds increase between this time frame Lance Whittingham IV specializes in buying deep...

show work....Assume that the average firm in your company's industry is expected to grow at a constant rate of 5 percent, and its dividend yield is 4 percent. You company is about as risky as the...

Illustration.1. Mr. Abdullah manufacturer of cement requested to Meezan bank Islamabad on January 1st2010, to issue cash for purchase of raw material amounting to Rs; 2 million for supply of 8,000...