Question: Determine the support reactions at and . Take E = 200 MPa, I = 300(10 6 ) mm 4 , A = 21(10 3 )

Determine the support reactions at ‘  and  ž‚. Take E = 200 MPa, I = 300(106) mm4, A = 21(103) mm2for each member.

- 5 m 300 kN · m, 3 9. (2, 4 m 2

- 5 m 300 kN m, 3 9. (2, 4 m 2

Step by Step Solution

★★★★★

3.33 Rating (168 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Partition matrix 0 851250D 1 22500D 3 22500D 4 0 1055760D 2 14400D 3 300 22500... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Structural Analysis Questions!

Q:

Determine the support reactions at the fixed supports and . Take E = 200 GPa, I = 300(10 6 ) mm 4 , A = 10(10 3 ) mm 2 for each member. 12 kN/m 1) 2 m - 4 m- 10 kN 2 m 6. (3'

Q:

Determine the support reactions at pins and . Take E = 200 GPa, I = 350(10 6 ) mm 4 , A = 15(10 3 ) mm 2 for each member. 2 60 kN 3 - 2 m 2 m 4 m 3) 9

Q:

Determine the support reactions at and . Take E = 29(10 3 ) ksi, I = 300 in 4 , A = 10 in 2 for each member. 2 k/ft A7 42 (2 6. 2 (3 3 20 ft 10 ft 8.

Q:

(a) What are the assumptions for plastic analysis of steel sections? 5 (b) Show that in a rectangular section subjected to axial force N and bending moment M, M M AREA = 300 mm + AREA = 450 mm N N P...

Q:

1 . A rigid beam ACEF is supported by a pin support at A and suspended from steel cablesBC and DE ( E = 2 0 0 , 0 0 0 MPa, = 0 . 3 , diameter 1 0 mm ) which are attached to pin supportsat B and D...

Q:

g) h) 5 KN 50 mm 20 mm 150 mm 40 mm 2 kN 200 mm 5 kN 1 kN Three forces are applied to member ABD as shown. The cross-section is a hollow rectangle with 20mm height and 40mm width and a wall thickness...

Q:

Assignment Questions Question 6 (Required knowledge: Stresses 2,4 & 5 lecture material) An old existing timber bridge with a concrete deck is currently in service in the south west of Western...

Q:

roblem 1 (35 pts): The beam ABC is fixed at A, hinged at B, and supported by a roller at C. The reactions at A and Care shown on the figure. Ignore axial and shear deformations. Take E= 200 GPa. l, =...

Q:

Use Ftool software for this numerical. Consider the following specifications for a concrete beam: Concrete isotropic material E = 2 2 0 0 0 0 MPa Beam length: 1 0 m Simply supported type, supported...

Q:

Problem 1: SPC - Penalty Method 3.10. Consider the bar in Fig. P3.10. Determine the nodal displacements, element stresses, and support reactions. 400 mm 250 mm 300 kN 600 kN 150 mm 150 mm 200 mm 200...

Q:

The compound-lever pruning shears shown can be adjusted by placing pin A at various ratchet positions on blade ACE. Knowing that 1.5-kN vertical forces are required to complete the pruning of a small...

Q:

Distinguish between full backups, incremental backups, and differential backups of files.

Q:

Typically, all other things equal, a profitable company that pays little or no dividends: 1 0 Multiple Choicepointsis a bad investment.eBookReferenceswill reinvest profits which can lead to greater...

Q:

For the data in Exercise 15.16, compute . How well does this equation fit compared with the optimal equation? Why should this be the case?

Q:

The pipe is made of A992 steel and is connected to the collars at A and B. When the temperature is 60°F, there is no axial load in the pipe. If hot gas traveling through the pipe causes its...

Q:

The pipe is made of A992 steel and is connected to the collars at A and B. When the temperature is 60°F, there is no axial load in the pipe. If hot gas traveling through the pipe causes its...

Q:

The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T 1 = 60°F. Each rod has a diameter of 1.25 in. Determine the average normal...

Q:

Does inflation have anything to do with making a dollar today worth more than a dollar tomorrow? And discuss how you could avoid inflation in relation to the time value of money? Answer 7 A, BI

Q:

How much would you need to invest to get a return of $1.00 from an investment with a price per share of $36 with earnings per share of $1.80? Answer $1.00 $1.80 $20 $35.20 $180.00 Buying shares of...

Q:

HOTEL RETURN WEIGHT (proporation of portfolio) RISK (standard deviaiton fo return) Hotel X 10% 75% 3% Hotel Y 20% 25% 9% 1. Given that the standard deviation of returns on the market is 10 percent,...