Question: Write the APT geometry statements to define the hole positions of the part. Use the lower left corner of the part as the origin in

Write the APT geometry statements to define the hole positions of the part. Use the lower left corner of the part as the origin in the x-y axis system.

Step by Step Solution

★★★★★

3.44 Rating (167 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Points are defined 10 mm above part surface for convenience i... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

795-C-S-A-I (478).docx

120 KBs Word File

Students Have Also Explored These Related Artificial Intelligence Questions!

Write the APT geometry statements to define the part geometry. Use the lower left corner of the part as the origin in the x-y axis system.

Write the APT geometry statements to define the part geometry.

Define the variables x and y as x = 5.1 and y = 4.2, then evaluate: (a) 3/4 xy 7x/y2 + xy (b) (xy)2- x + y/(x-y)l2 + x + y/2x - y

Write the APT geometry statements to define the hole positions of the part. Use the lower left corner of the part as the origin in the x-y axis system. Discuss.

Write the APT geometry statements to define the outline of the part. Use the lower left corner of the part as the origin in the x-y axis system.

Write the complete APT part program to perform the profile milling operation for the partQ 1 3 . Write the complete APT part program to perform the profile milling operation for the part drawing in...

Write the complete APT part program to profile mill the outside edges of the part. The part is 15 mm thick. Tooling = 30 mm diameter end mill with four teeth, cutting speed = 150 mm/min, and feed =...

Write the complete APT part program to perform the profile milling operation for the part drawing in Figure P7.29. Tooling = 20 mm diameter end mill with two teeth, cutting speed = 125 mm/min, and...

The part is to be drilled on a turret-type drill press. The part is 15.0 mm thick. There are three drill sizes to be used: 8 mm, 10 mm, and 12 mm. These drills are to be specified in the part program...

ISE 4 7 0 HW 3 2 0 points. Due the end of 1 5 Oct. Write the part program to drill the holes in the part in Figure below ( Unit: mm ) . The part is 1 2 . 0 mm thick. Cutting speed \ ( = 1 0 0 \...

Consider an ideal Sterling cycle using air as the working fluid. Air is at 350 K and 200 kPa at the beginning of the isothermal compression process, and heat is supplied to air from a source at 1800...

How are innovation processes in the process perspective linked to the Balanced Scorecards customer and financial perspectives?

In 2 0 X 2 , management at Blue Flower Company increased the estimated useful lives of its equipment by 5 0 % . In 2 0 4 , it was determined that the service lives had been overestimated in order to...

Recall an instance in which you read or heard about empirical research that you suspected was flawed. Briefly describe why you suspected that.

What is the minimum overhead to send an IP packet using PPP? Count only the overhead introduced by PPP itself, not the IP header overhead.

For this problem, use a formula from this chapter, but first state the formula. Frames arrive randomly at a 100-Mbps channel for transmission. If the channel is busy when a frame arrives, it waits...

A group of N stations share a 56-kbps pure ALOHA channels. Each station outputs a 1000-bit frame on an average of once every 100 sec, even if the previous one has not yet been sent (e.g., the...

Kim is diligent and, starting on her 1 8 th birthday, she saves $ 1 2 0 0 and continues her annual savings ( on her birthdays ) until her 2 5 th birthday. After the deposit on her 2 5 th birthday she...

KADS, Inc. has spent $410,000 on research to develop a new computer game. The firm is planning to spend $210,000 on a machine to produce the new game. Shipping and installation costs of the machine...

What is the IRR?of this investment opportunity if your cost of capital is 8 . 6 % . Should you make the investment? Calculate the IRR and use it to determine the maximum deviation allowable in the...