Question: Write the APT geometry statements to define the hole positions of the part. Use the lower left corner of the part as the origin in

Write the APT geometry statements to define the hole positions of the part. Use the lower left corner of the part as the origin in the x-y axis system. Discuss.

Step by Step Solution

★★★★★

3.43 Rating (175 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Points are defined 10 mm above part surface for convenience in subsequen... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

795-C-S-A-I (480).docx

120 KBs Word File

Students Have Also Explored These Related Artificial Intelligence Questions!

Write the APT geometry statements to define the part geometry. Use the lower left corner of the part as the origin in the x-y axis system.

Write the APT geometry statements to define the part geometry.

Write the complete APT part program to profile mill the outside edges of the part. The part is 15 mm thick. Tooling = 30 mm diameter end mill with four teeth, cutting speed = 150 mm/min, and feed =...

Write the APT geometry statements to define the hole positions of the part. Use the lower left corner of the part as the origin in the x-y axis system.

Write the APT geometry statements to define the outline of the part. Use the lower left corner of the part as the origin in the x-y axis system.

Write the complete APT part program to perform the profile milling operation for the partQ 1 3 . Write the complete APT part program to perform the profile milling operation for the part drawing in...

Write the complete APT part program to perform the profile milling operation for the part drawing in Figure P7.29. Tooling = 20 mm diameter end mill with two teeth, cutting speed = 125 mm/min, and...

The part is to be drilled on a turret-type drill press. The part is 15.0 mm thick. There are three drill sizes to be used: 8 mm, 10 mm, and 12 mm. These drills are to be specified in the part program...

ISE 4 7 0 HW 3 2 0 points. Due the end of 1 5 Oct. Write the part program to drill the holes in the part in Figure below ( Unit: mm ) . The part is 1 2 . 0 mm thick. Cutting speed \ ( = 1 0 0 \...

Write the part program to drill the holes in the part shown in Figure P7.26. The part is 12.0 mm thick. Cutting speed = 100 m/min and feed = 0.06 mm/rev. Use the lower left corner of the part as the...

Team project Gain additional insight into the proof of Cauchy??s integral theorem by producing (2) with a contou enclosing z0 (as in Fig. 353) and taking the limit as in the text. Choose and (c) Two...

Using loop analysis, find I0 in the network shown. 12ZTV 2 2 I,

Theta Ltd. in a business which acts as a distributor of washing machines entirely on credit term to a wide range of customers. The following balances were extracted from its ledgers at 30th June,...

Do you think that the opinions of your friends and acquaintances are good predictors of the outcomes of elections? Why? Why not?

Measurements of a slotted ALOHA channel with an infinite number of users show that 10 percent of the slots are idle. (a) What is the channel load, G? (b) What is the throughput? (c) Is the channel...

In an infinite-population slotted ALOHA system, the mean number of slots a station waits between a collision and its retransmission is 4. Plot the delay versus throughput curve for this system.

How long does a station, s, have to wait in the worst case before it can start transmitting its frame over a LAN that uses (a) The basic bit-map protocol? (b) Mok and Ward's protocol with permuting...

The Prince-Robbins partnership has the following capital account balances on January 1, 2018: Prince, Capital Robbins, Capital $ 50,000 40,000 Prince is allocated 70 percent of all profits and losses...

Two mutually exclusive projects are under consideration with the details shown. The company's required rate of return for projects of this risk level is 16%, using this information, answer the...

Soprano Co. is in the process of preparing the second quarter budget for 2019, and the following data have been assembled: The company sells a single product at a selling price of $41 per unit. The...