Question: how to make a full adder and test it on breadboard with a battery holder red and black wire? without a resistor only 2 leds.

how to make a full adder and test it on breadboard with a battery holder red and black wire? without a resistor only 2 leds.
can you show me how you implement it on the breadboard? (the final design)

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

I need help with my lab's data table R1-9.8, R2-30.7, R3-99.03 V1-33.4 V2-32.5 Lab-10A (LK) Kirchhoff's Rules Objective 1. Learn to build up a complicated circuit by using two DC power supplies and...

Q:

I need help with this labs data table R1-9,R2-35,R3-98 battery 1-33.8 battery 2-32.5 That all I have 3.5. Parallel connect the voltage sensor across resistor Ry (across $2 and $6), the sensor will...

Q:

Procedure 1. Implementation Implement the datapath on a breadboard and ensure that every operation works as expected. It is highly recommended that you adopt an incremental approached to the...

Q:

1102L-080/081; Lab 05 Rabbit year, Sum2, 2023 Simulation created by the Physics Education Technology Project (PhET) c/o The University of Colorado at Boulder http://phet.colorado.edu/ 1 Lab 5: DC...

Q:

In this project you will build a traffic light controller using only registers ( D - flip flops ) and basic logic gates ( AND , OR , NAND, NOR, NOT ) . The Problem You are modeling the lights for a...

Q:

8. Build a circuit consisting of a light bulb and a battery (similar to Figure 4.2). Click on the battery and adjust the voltage using the slider. How does varying the voltage affect the light bulb...

Q:

Arizona State University LO2 CIRCUIT LAB 1 INTRODUCTION You will explore properties of electricity in circuits via a PhET virtual lab. 2 MATERIALS For this virtual electricity lab, you will be using...

Q:

STEP 1 With the power to your bread boa rd off, build the circuit shown in the schematic below. Notice that you should be using red LE D5 in this lab. // D1 02 P33 Red Red 5 v R1 220 Q // Turn the...

Q:

I only need help with "midterm changes requierement" part 2. Wiring Connections All wire connections in Red are external wires from your breadboard to the demo connectors. 1- The entire breadboard is...

Q:

can anyone do that please ? EL-100 LAB #2 CHOD Measuring DC Current, Voltage, and Resistance OBJECTIVE: To become proficient in the construction of simple circuits on the ET 3600 Trainer and...

Q:

During the current year, 40 acres of land that cost $200,000 were condemned for construction of an interstate highway. Assuming that an award of $320,000 in cash was received and that the applicable...

Q:

Johnson Inc. is a job-order manufacturing company that uses a predetermined overhead rate based on direct labor-hours to apply overhead to individual jobs. For 2010, estimated direct labor-hours are...

Q:

The change of large firms more supports the pecking order theory. The change of small firms more supports the trade - off theory. Small firms have moved toward more flexible capital structures. Large...

Q:

SOLVE USING PYTHON, DO NOT ANSWER WITH MATLAB CODE. PYTHON ONLY. ANSWER WILL BE DOWN VOTED IF NOT SOLVED IN PYTHON. PO Im...! x 7 10.44 Two tanks of cross-sectional areas A, and A2 are intercon-...

Q:

Explain the difference between Job Analysis, Job Classification, and Job Evaluation.

Q:

What does Processing of an OLAP Cube accomplish?

Q:

After designing a Multidimensional Database in Visual Studio, what are the next steps that build the Database in the Analysis Services Instance? How is the build out of the Analytical Services...