Question: In a turning, operation, chip thickness was found to be 0 . 6 mm , feed = 0 . 2 mm / rev , rake

In a turning, operation, chip thickness was found to be 0.6 mm, feed =0.2mm/rev, rake angle 15 Calculate chip reduction co-efficient, cutting ratio, shear angle, frictional angle.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Problem 13.18 and Exhibit 13.7 in Chapter 13 present selected hypothetical data from projected financial statements for Steak 'n Shake for Year +1 to Year +11. The amounts for Year +11 reflect a...

Q:

It was found from experiments where the chips produced during shap - ing were caught in a calorimeter that the mean chip - temperature rise was 5 0 0 C . The cutting conditions were as follows:...

Q:

2 0 . 5 ( A ) ( USCS units ) A turning operation is performed using a rake angle of 1 5 . Cutting speed = 2 0 0 f t m i n , feed = 0 . 0 1 2 i n r e v , and depth of cut = 0 . 1 0 0 i n . The chip...

Q:

1. Shear plane angle and shear strain: In an orthogonal cutting operation, the tool has a rake angle = 15. The chip thickness before the cut = 0.31 mm and the cut yields a deformed chip thickness =...

Q:

A 1 3 . 5 mm diameter steel shaft is made from a 1 5 mm round bar in one pass. The chip thickness was measured to be 1 . 8 mm . The cutting force was measured to be 1 kN . The spindle is rotating at...

Q:

In a turning operation, a cylindrical workpiece with an initial diameter of 1 5 0 mm and a length of 7 0 0 mm is being machined with a spindle speed of 1 0 0 0 RPM and a feed rate of 0 . 3 5 m m r e...

Q:

Consider the straight turning operation of a AISI 1 0 1 0 steel bar with a tool with a rake angle of 5 and a clearance angle of 3 , using the following operating parameters: cutting speed is 3 1 5 m...

Q:

Answer all 4 questions A turning operation is performed on an engine lathe using a tool with zero rake angle in the direction of chip flow. The work material is an alloy steel with hardness =325...

Q:

Q1) Determine the cutting force and feed (thrust) force for a turning operation using following parameters: Material tensile strength 250MPa, Shear strength 120 MPa, chip thickness ratio r = 0.45,...

Q:

Q1) Determine the cutting force and feed (thrust) force for a turning operation using the following parameters: Material tensile strength 250MPa, Shear strength 120 MPa, chip thickness ratio r =...

Q:

5 0 Points ) A turning cutting tool with a major cutting - edge angle of 9 0 \ deg and a minorcutting edge angle of 1 0 \ deg and rake angle of 1 0 \ deg is used on a 1 kW lathe to turn a 5 0...

Q:

(a) Show that it was valid to ignore the gravitational force in Problem 97. In problem 97 A negatively charged particle of mass 5.00 1019 kg is moving with a speed of 35.0 m/s when it enters the...

Q:

The rules are as follows. The shooter rolls two dice. If the first roll is 2, 3, or 12 the shooter loses. If the first roll is 7 or 11, the shooter wins. If the first roll is anything else, that...

Q:

1 . A 9 0 - day Province of Ontario T - bill with a $ 3 5 , 0 0 0 face value matures on December 1 1 , 2 0 2 2 . Farrah works forHearthplace Industries and notices that the company temporarily has...

Q:

Empire State Carpets' books show the following data. In early 2026, auditors found that the ending merchandise inventory for 2023 was understated by $8,000 and that the ending merchandise inventory...