Question: When the interrupt flag is set ( IF = 1 ) in the 1 6 - bit flag register, then the INTR pin _ _

When the interrupt flag is set (IF=1) in the 16-bit flag register, then the INTR pin _________.
Is ignored
Can cause an interrupt
Is set low
Is NMI

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

Microcontroller is ATXMEGA128A1U in assembly 5.3 Write the interrupt service routine for TCCo timer/counter overflow. Perform the following operations in the service routine: (1) Check to see if the...

Q:

Try to use these Asm. Language commands we use so far in the class.MOV AL , 4 Ah ; Move to the AL register the value 4 A ( 1 6 ) = 7 4 ( 1 0 ) MOV AL , BL ; Copy the value of the BL register to the...

Q:

Complete Passing Mark Score: Exercise Lab Work in your own words, write a short paragraph for each of the following questions from the assigned readings Question 1 1.6. Consider a computer system...

Q:

You can use the C + + language to: create a variable and give it an initial value ( except for array filling ) . In all other cases, Assembly language instructions must be used. Part 1 tasks: ( 1...

Q:

microcontroller 8051 (MPC82G516A) to finish square wave generation. (timer) question fig. microcontroller 8051 (MPC82G516A) to finish square wave generation. some code picture number is 10626140...

Q:

The first microprocessor had a ( n ) . 1 bit data bus 2 bit data bus 4 bit data bus 8 bit data bus A 2 0 - bit address bus can locate. 1 , 0 4 8 , 5 7 6 locations 2 , 0 9 7 , 1 5 2 locations 4 , 1 9...

Q:

need help in code composer for the three objectived listed above, preliminary code provided 1- Interrupts and Programming Model Interrupts will be discussed in the lecture but in a nutshell they are...

Q:

TF 1 , TR 1 , TF 0 , TR 0 bits are of which register? TMOD SCON TCON SMOD Clear selection The contents of a base register are added to the contents of index register in indexed addressing mode based...

Q:

I need help fixing my portF registers so my C-PROGRAMMING code can work. It is a two push-button code for the TM4C123G LaunchPad. #include "tm4c123gh6pm.h" // device specific include file #define...

Q:

Please use tinkercad The overall goal of this assignment is to become familiar with the basic use and configuration of timers. You will learn how to configure and access the timer registers to create...

Q:

As a result of the Analysis of Simulation results and As an CEO of Sunflower Nutraceuticals (SNC), in preparation for your presentation to board of directors of SNC, you will write a memo describing...

Q:

A student is working with the circuit shown in the diagram below. She uses an ammeter and finds that the current through the branch with the 300-2 resistor to be I = 0.050 A. (a) What is the voltage...

Q:

This substance causes a feeling of transient euphoria followed by a general depression.

Q:

Any negligence of the part of the plaintiff is a complete bar to recovery in: Group of answer choices a comparative negligence state a contributory negligence state a concurrent negligence state a...

Q:

This book covers four human resource management practice areas: managing the human resource environment, acquiring and preparing human resources, assessment and development of human resources, and...

Q:

Carry out a risk assessment exercise for an activity that you take part in. It might be a local amateur football or netball team, drama event or similar.

Q:

Many have suggested that OSHA penalties are too weak and misdirected (aimed at employers rather than employees) to have any significant impact on employee safety. Do you think that OSHA-related...