Question: do this using tinkercad please both tasks Build a circuit with LEDs and a pushbutton 1.1. Build the circuit shown below using 3 LEDs (Red,

do this using tinkercad please both tasks

Build a circuit with LEDs and a pushbutton 1.1. Build the circuit shown below using 3 LEDs (Red, Yellow and Green) and a pushbutton as input from the user. Each LED is connected through a 390 resistor to a digital pin, note that the pushbutton is connected through a pullup resistor (10K ). Take a photo of your circuit and copy it on the Lab Assignment 5_answer sheet at BB under Task 1_Ciruit. [20\%] 1.2. What is the purpose of using the resistor 10K ? [10%] ... TQ. . limit. the . current. Hiow. Hrough. . He lED. and to prenent... the excess. Curent. that. con burn. aut. or. in other. words to .. control the brightness. . Of .. the. (LED. J. Using a pushbutton as a user input to control the LEDs 2.1. Write a code that would make the Red LED turn on when the pushbutton is pressed and the green will be on when the pushbutton is released. Include your comments to explain your code. Copy it to Lab Assignment 5_answer sheet at BB under Task 2. [20\%]

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

In this assignment, you will develop a simple traffic light control system for a four - way street intersection using Arduino Uno board. At the minimum, you must prepare 2 sets of traffic lights (...

Note: you can run the code and test the circuit via tinkercad but I will be using the code in an actual arduino uno board so I'll be needing a code that will run in an actual arduino uno board....

do it using tinkercad and breadboard with arduino provide for each task a code and circuit screenshot Build a circuit with LEDs and a pushbutton 1.1. Build the circuit shown below using 3 LEDs (Red,...

Design an embedded system application using Tinkercad to simulate a traffic light sequence by writing to and reading from digital pins. Instructions: 1. Click on "Create new circuit" and add the...

Please give me the code and explain it MEMORY GAME objectives After performing this lab, the students should be able to: Write a C program to simulate a memory game using an Arduino Uno board....

Task 1 : Servo motor control using a potentiometer Connect the servo motor and potentiometer to the Arduino as below. Write down your code to control the servo position using a potentiometer. Task 2...

do it using tinkercad and breadboard with arduino provide for each task a code and circuit screenshot 3.1. Write a sketch code to achieve the functionality of the manual traffic light by achieving...

SOLVE USING TINKERCAD (CODE) Circuit building with an Arduino Note: Please use Tinkercad Assessment Build a 4-bit binary adder "O" is represented as led "Off" "1" is represented as led "On" Decimal...

STEP 1 With the power to your bread boa rd off, build the circuit shown in the schematic below. Notice that you should be using red LE D5 in this lab. // D1 02 P33 Red Red 5 v R1 220 Q // Turn the...

In this project you will build a traffic light controller using only registers ( D - flip flops ) and basic logic gates ( AND , OR , NAND, NOR, NOT ) . The Problem You are modeling the lights for a...

Multinationals generally have production plants in a number of countries. Consequently, they can move production from expensive locations to cheaper ones in response to various economic developmentsa...

(Preparing an income statement) Prepare an income statement and a common-sized income statement from the following information. Sales $525,958 Cost of goods sold 199,257 General and administrative...

What is physical address and logical address?

SIMAD UNIVERSITY Class: BACC25 Subject: Islamic Accounting Instructions: a) Follow The Instructions. Midterm Exam Instructor: All Ibrahim Date: 6-4-2022 b) You Have 1.5 Hrs. To Complete This Test. c)...

B Do you have a page on Facebook, MySpace, or some other social networking site? Think objectively about the impression of you that the page conveys. Would you hire you?

4 How can you create a better online image for yourself?

Tell me about yourself. What led you to choose your particular field (or your academic major)? Describe your level of satisfaction with your choice.